Custom Hinges | Hoffman Hinge & hardware
Hoffman Hinge and Hardware HomeHingesAbout Hoffman Hinge and HardwareHinge TerminologyHinge ApplicationsContact Hoffman HingeGet a Hinge Quote
Custom Hinges

Return to "Standard Hinge Terminology

Custom Hinges:

Does your project require a special hinge? Hoffman Hinge can design a custom hinge fabrication to meet your exact specifications. We stock a wide variety of materials and offer superior turnaround time. If your project requires a custom designed hinge, please be sure to include the following with your order:

•  Dimensions of your project
•  Type of hinge needed (i.e, continuous)
•  Hinge material
•  A sketch or drawing of your schematic
•  Any other pertinent details such as material type of door, left- or right-handed hinge

Heavy Duty Hinge

Contact Hoffman Hinge and Hardware to talk to one of our experienced sales persons or engineers or submit your inquiry and receive a custom hinge quote.

Continuous hinges can be cut to exact length as required. Hinges should, however, be designed to a length that is a multiple of the knuckle length to eliminate partial knuckles. If a partial knuckle length cannot be avoided, please keep the following points in mind: 1) partial knuckle lengths should be the same as or larger than the knuckle diameter; 2) when partial knuckles are required on both ends, they should be on the same leaf; 3) please be advised that continuous hinges with partial-end knuckles on one leaf may not rotate as freely as full-end knuckles.

Industrial HingesPIN RETENTION
All standard continuous hinges are stocked with loose pins and flush cut ends, with the exception of steel and stainless steel hinges in thicknesses of .025 and .035" which will be staked to retain the pin. The following are among the methods used to retain the pins.

Flush pin staked
The most economical way to retain a pin is by staking it on the topside or backside of the knuckle.

Pin spun both ends
This method is normally used only for tamper-proofing or for applications with severe vibrations.

All standard hinges are supplied with like pin and leaf materials. However, any hinge can be ordered with a pin material different from its leaf material. For example, you may request steel hinges with brass pins.

Many designs for piercing are available. When ordering or requesting a special hinge quotation, include: hinge dimensions, hole diameter and type, hole centers, edge dimensions and end dimensions. Ask about our standard hole patterns. Following are several common piercing designs:

Custom Hinge Supply
Special Hinges

Note: Countersinking is the removal of metal, whereas coining is the displacement of metal, and in some cases will leave a slight bulge on the leaf edge.

Formed special hinge leaves can be supplied in a variety of configurations (including those illustrated below). Dimensions should be taken from the pin center line and inside of forms. Unless otherwise indicated, the inside radius of a form is the same as the material thickness.

Custom Hinge Products

Unequal leaves are available on all hinges. Widths are measured from the pin center line to the leaf's outer edge. For the most economy, unequal open width should be a product of a standard hinge width; however, unequal leaves with nonstandard widths are also available.

Notched Leaves

Some of the more commonly used designs:

Hinges can be pierced and installed with self-clinching fasteners per customer specifications.

Any of our standard continuous hinges can be spring loaded. This type of hinge is produced using torsion springs, complying with your specifications. When ordering, include a sketch that indicates spring action (open or closed), locations, force, material and all other pertinent information.

Custom Slip Joint Hnges
Slip joint hinges or "take-apart" hinges are normally used when requirements call for doors to be removed. Indicate right- or left-handed when ordering.

Our butt hinges come with either tight or loose pins, according to your specifications.

Custom Butt Hinges

Multiple Pin Hinges
Multiple pin hinges allow for double action, as required.

A variety of plated finishes are available upon request: zinc (clear, yellow and black), cadmium, nickel, brass and lacquer, anodized (satin, black, gold and bronze), electropolished, painted or pre-painted, etc.

Note: Hinges will be plated assembled. Only hinges shipped to customers unassembled will be plated unassembled. Aluminum hinges cannot be anodized with brass or stainless steel pins.

Return to "Standard Hinge Terminology

Home | Hinges | Custom Hinges | About Us | Hinge Terminology | Hinge Applications | Contact Us | Get a Hinge Quote

Hoffman Hinge and Hardware, LLC
11750 Marlboro Avenue NE
Alliance, Ohio 44601

©2005-2013. All rights reserved.

PH: (330) 935-2240
FAX: (330) 935-2197

Contact Us
Site Map